Raptor 30 v2 manual espaol

No puedo ayudarte amigo. Gerardo el 17 de junio de a las Gracias Responder. Gerardo el 28 de junio de a las Control Dron el 18 de abril de a las Nilsen Grajales el 24 de abril de a las Antonio el 27 de mayo de a las Gaspar Fdez-Lomana el 2 de junio de a las Muchas gracias Responder.

Montse comas el 2 de julio de a las Hola tendrian el manual de instrucciones en castellano del dron sg Pro, en la compra ponia que vendrian en castellano, pero no ha sido asi Muchas gracias Responder. Julio el 20 de julio de a las Antonio el 4 de agosto de a las Tengo un Dron el SG pro y me gustaria saber como se puede programar un vuelo para luego pasarlo a coordenadas, Responder.

Rafael Martinez cornejo el 17 de diciembre de a las Quisiera saber como conectar el dron sg pro2 y el dji mini 2 a las gafas eachine ev porque yo soy incapaz de conectarlo gracias Responder. Santiago el 5 de enero de a las Hedixon Cadena el 17 de abril de a las Pedro el 13 de agosto de a las Pedro el 20 de agosto de a las Gracias de todas formas, un saludo Responder.

Control Dron el 20 de agosto de a las If you put the hole plate towards the blades, during flight the plate will be pressed to the outer scale by centrifugal force.

In that case a bearing ball can roll over the plate which would ruining the bearing. Also available is a very low quality parts list in german. In contrast with the Raptor 30 manuals, a Raptor 50 manual has never been made available in electronic form by Thunder Tiger.

Therefore this manual was constructed partly by scanning in parts and by manually creating the pages, and partly by copying and modifying the Raptor 30 V2 manual.

I did a very careful job in duplicating the manual, but of course I can not assume responsibility in case of errors. The duplicate has been kept as close as possible to the original manual, but at numerous places errors and typos were corrected. At many places the English text was improved, as well as the layout. Some part numbers have been corrected. A few sentences where correction would need more than changing a few words were left unchanged.

Assembling Section Flight Training Section Maintenance Section Blade Modification Previous Page. Next Page. Thunder tiger fun tiger extra; fun tiger g model aircraft 20 pages. It is the most popular size helicopter in the world. The Raptor 30 has helped experienced pilots learn new 3-D maneuvers. Page 2 with a liability insurance plan as well as monthly magazine entitled Model Aviation.

All AMA charter aircraft clubs require all pilots to hold a current AMA sporting license prior to operation of their models at club fields. The part number and quantity contained in each are always shown in the square box on each page. Do not open all the bags at once. Open only the bag Also, a fuel filter available from any hobby 3 BK shop, TTR should be placed between the fuel tank and the carburetor.

Page 6 3 Main Frame Assembly-Part1 Please insert the frame spacers, bearings, pulley and parts in the frames according the drawing below. Tighten the screws snugly, but do not over torque them which could strip the plastic. Insert starter shaft through the center of the clutch bell assembly, through the top starter shaft bearing and into the starter coupling.

Attach the linkage rod to the parallel elevator linkage balls. Page 9 7 Main Frame Assembly-Part3 Insert Main Shaft through the shaft bearings making sure that the end with the holes closest to the end is pointed down. Next, slide main gear assembly into position on the shaft and line up the holes in the main shaft with the holes in one way clutch shaft of the main gear assembly. Page Engine Assembly 9 Engine Assembly Note: A piston lock purchased from your dealer will make this a much easier task.

When screwing on the flybar paddles to the flybar, stop when you can see the rod in the window of the paddle. Then, lay the assembly on a flat surface and align the paddles so they are exactly parallel. Page 12 12 Main Frame Assembly-Part5 Slide the main Rotor assembly over the main shaft and align the two pins to slide in the washout assembly.

Make sure the holes in the main shaft line up with the holes in the main rotor head. Insert the socket screw and secure with locknut. Then slide the tail linkage rod into the rod guides. Next, insert the tail rotor drive belt into the boom so that it comes out of both ends.

Place drive belt over tail drive pulley and complete balance of tail boom assembly. Page 14 16 Servo Installation-Part1 Assembly Tip: Remove all the servo wheels prior to attaching the steel linkage balls. Make sure all linkages are the correct length.

Page 15 17 Servo Installation-Part2 Assembly Tip: Remove all the servo wheels prior to attaching the steel linkage balls. Neatness counts, so take your time.

The three different scales are designed for beginner, intermediate or expert F3C and 3D pilots. Page 20 10mm The above pushrod lengths will permit 3D with the Raptor. Use these lengths as a starting point. Beginners can also use those pushrod lengths, but just connect the collective control to the outside point on the pitch control arm. Pushrod lengths are measured from ball link center to ball link center.